home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.01 seconds.
Search: Posts Made By: Lankku
Forum: projects & restorations 01-14-2020, 06:18 PM
Replies: 192
Views: 61,014
Posted By Lankku
700 has 48 teeth from model year -89 and up. 240...

700 has 48 teeth from model year -89 and up. 240 without ABS got it in -91 or -92.


3.31 works with Truetrac as does any other. Ratio doesn't affect the fitment.
Forum: performance & modifications 01-14-2020, 06:11 PM
Replies: 15
Views: 630
Posted By Lankku
I've never replaced the M10 bolts. I think I've...

I've never replaced the M10 bolts. I think I've used the same ones three or four times when rebuilding or for whatever reason the engine has been opened before swapping another block. Zero issues.
Forum: performance & modifications 01-06-2020, 02:01 PM
Replies: 68
Views: 2,208
Posted By Lankku
They are .008 or .016 above. Can't remember which.

They are .008 or .016 above. Can't remember which.
Forum: performance & modifications 01-06-2020, 01:45 PM
Replies: 15
Views: 630
Posted By Lankku
Here you can see recommended numbers for ARP...

Here you can see recommended numbers for ARP bolts: https://www.raceeng.com/techsheets/eagle_pdf.pdf
Forum: performance & modifications 01-06-2020, 12:18 PM
Replies: 15
Views: 630
Posted By Lankku
Don't have any to give at this point but they are...

Don't have any to give at this point but they are the same as 4- and 5-cyl and RWD 6-cyl.
Forum: performance & modifications 01-04-2020, 07:33 AM
Replies: 26
Views: 1,067
Posted By Lankku
If the shock is that short, it might/will bottom...

If the shock is that short, it might/will bottom out on rebound. Or they might even compress the springs and lower the car just because they are so short. Needs shorter springs.
Forum: performance & modifications 01-04-2020, 07:31 AM
Replies: 68
Views: 2,208
Posted By Lankku
Doesn't look too bad. Just grind the sharp edges...

Doesn't look too bad. Just grind the sharp edges and send it. Though check the valves and seats, there might be aluminium pieces and they won't seal.
Forum: maintenance & nonperformance 12-31-2019, 06:11 PM
Replies: 4
Views: 419
Posted By Lankku
The bearing will not cause any rattle unless it's...

The bearing will not cause any rattle unless it's worn out.
Forum: maintenance & nonperformance 12-31-2019, 06:09 PM
Replies: 16
Views: 884
Posted By Lankku
Most likely it is stuck in the oil pickup in the...

Most likely it is stuck in the oil pickup in the sump. If it happens to go through the pickup, I think the oil pump does not care(too much) because it's soft and there is not a lot of it. Oil filter...
Forum: maintenance & nonperformance 12-31-2019, 06:05 PM
Replies: 9
Views: 619
Posted By Lankku
Rear wheels shoud rotate with all fours up in the...

Rear wheels shoud rotate with all fours up in the air. Does the prop shaft rotate or not?
Forum: maintenance & nonperformance 12-31-2019, 02:37 PM
Replies: 4
Views: 419
Posted By Lankku
With a hydraulic clutch the release bearing is...

With a hydraulic clutch the release bearing is always slightly pressing the pressure plate.
Forum: projects & restorations 12-25-2019, 06:05 PM
Replies: 123
Views: 61,923
Posted By Lankku
Recently bought poly bushings for -92 rear upper...

Recently bought poly bushings for -92 rear upper control arms and installed them to the axle side. The small flex they have reduces noise a lot. Got the car inspected and now all mods worth approving...
Forum: performance & modifications 12-25-2019, 09:44 AM
Replies: 16
Views: 946
Posted By Lankku
If it's not a M46 then it has been changed. As...

If it's not a M46 then it has been changed. As far as I know all manual 200, 700 and early 900 turbo cars had M46 from the factory.

M47 would be the most obvious choice unless someone has...
Forum: maintenance & nonperformance 12-14-2019, 07:55 AM
Replies: 7
Views: 647
Posted By Lankku
Wont be a problem. If I remember correctly, 4th...

Wont be a problem. If I remember correctly, 4th gear is recommended for towing heavy loads and I'd use it. You'll need it anyway, stock engines don't have enough power for uphills on 5th gear.
Forum: projects & restorations 12-11-2019, 01:53 PM
Replies: 36
Views: 2,899
Posted By Lankku
To me the pics do not show a lot of damage. I'd...

To me the pics do not show a lot of damage. I'd repair it without thinking any other options.

If there is a door shell on the estimate, has the outer metal warped and can't just be sanded down...
Forum: projects & restorations 12-07-2019, 04:03 PM
Replies: 123
Views: 61,923
Posted By Lankku
Painted the cage and rust repairs with black...

Painted the cage and rust repairs with black epoxy. Hood got two cans of old semi-gloss white rubber comp. At least it's not anymore peeling yellow.
...
Forum: projects & restorations 12-07-2019, 06:44 AM
Replies: 123
Views: 61,923
Posted By Lankku
It's a line for the pump which pumps air near...

It's a line for the pump which pumps air near exhaust valves after a cold start. You can plug the line and remove the pump if your regulations don't require it. Looks like someone already has removed...
Forum: projects & restorations 12-06-2019, 07:17 PM
Replies: 123
Views: 61,923
Posted By Lankku
Adding a cage, half or full, won't affect too...

Adding a cage, half or full, won't affect too much because everything is in front of the rear axle. Still can fit a 6-cyl whiteblock or two if I need to ;-)
Forum: maintenance & nonperformance 12-06-2019, 07:10 PM
Replies: 5
Views: 621
Posted By Lankku
Most likely your hinges are just worn. Is there...

Most likely your hinges are just worn. Is there play if you open the door a bit and lift it from the back corner? If so, then new pins or good used hinges from a left side back door.

Hinges have...
Forum: projects & restorations 12-06-2019, 04:53 PM
Replies: 123
Views: 61,923
Posted By Lankku
I'd say that frame rail and engine mount will be...

I'd say that frame rail and engine mount will be in the way of a bottom mount. Might be possible by using B6284T exhaust manifolds(they are flat) there could be just enough room for a HX35 size...
Forum: maintenance & nonperformance 11-26-2019, 01:52 PM
Replies: 17
Views: 1,603
Posted By Lankku
I've used different brands of basic 75W-90...

I've used different brands of basic 75W-90 synthetic, Redline Shockproof Light and Heavy. Never any noise.
Forum: projects & restorations 11-25-2019, 07:55 PM
Replies: 29
Views: 5,727
Posted By Lankku
I think breaking the bolt has something to do...

I think breaking the bolt has something to do with time and heat cycles and the place of the bolt. On some cases there has been dried oil in the bolthole while others are clean. But all stumps have...
Forum: projects & restorations 11-25-2019, 06:28 PM
Replies: 29
Views: 5,727
Posted By Lankku
Was it on the exhaust side between cylinders 4...

Was it on the exhaust side between cylinders 4 and 5? I've broken around 7 or 8 bolts(or more) on that spot. Some B6254, most B6284T and might be one B6304. All of them were opened the first time...
Forum: performance & modifications 11-24-2019, 07:03 PM
Replies: 6
Views: 1,181
Posted By Lankku
4" thickness means a bit more work on making it...

4" thickness means a bit more work on making it fit but otherwise not bad. Generic ones are usually 3" and go in much nicer.

If the outlets are pointing straight to the side I would cut them off...
Forum: performance & modifications 11-15-2019, 08:19 AM
Replies: 10
Views: 1,483
Posted By Lankku
Maybe someone has done it, but I don't see why...

Maybe someone has done it, but I don't see why would you. You'd have to make a bellhousing by joining new and old, drill new holes into the flexplate for the torque converter and machine a sleeve to...
Forum: projects & restorations 10-24-2019, 04:01 PM
Replies: 123
Views: 61,923
Posted By Lankku
On Tuesday changed new bushings to replace mushy...

On Tuesday changed new bushings to replace mushy upper rear control arms of the -92. From Opel Vectra B(Chevrolet Vectra in the States?) to be exact. They are ball joint-type and allow the control...
Forum: performance & modifications 10-24-2019, 07:22 AM
Replies: 13
Views: 2,471
Posted By Lankku
For me BC front struts have worked great. Had the...

For me BC front struts have worked great. Had the same pair in 4.6 V90 and 965 and now a pair in -92 245. Have also used Gaz shocks with coilover conversion and liked it. But BC is a "bolt-on" with...
Forum: maintenance & nonperformance 10-21-2019, 05:39 PM
Replies: 1
Views: 568
Posted By Lankku
The jet could be meant to be adjusted, depending...

The jet could be meant to be adjusted, depending on the age of your carburettor. But it doesn't really have an adjusting screw.

Older ones have a plug/screw on the bottom for a special tool to...
Forum: performance & modifications 10-17-2019, 05:23 PM
Replies: 21
Views: 2,295
Posted By Lankku
Having a power steering pump with a supercharger...

Having a power steering pump with a supercharger needs some measuring and making brackets. Didn't use one in my builds though. Best choice would be installing the supercharger under the intake(if you...
Forum: maintenance & nonperformance 10-12-2019, 06:52 AM
Replies: 3
Views: 576
Posted By Lankku
B19/etc. have a half moon on the back of the...

B19/etc. have a half moon on the back of the head. Haven't seen one in B2xx.
Forum: projects & restorations 10-11-2019, 04:14 PM
Replies: 123
Views: 61,923
Posted By Lankku
Installed Federal RS-R 205/50 semi-slicks on to...

Installed Federal RS-R 205/50 semi-slicks on to Hydras and swapped them under the -92. Removed sidetrims and spare wheel, filled the tank and today weighed the car. On paper stock car is...
Forum: performance & modifications 10-11-2019, 04:22 AM
Replies: 3
Views: 1,064
Posted By Lankku
JP-styling has been in existence for a long time...

JP-styling has been in existence for a long time so I'd say the company is legit.

Back in the day they sold Viking chips. Don't know if those are just copies with their name on or have they made...
Forum: projects & restorations 10-08-2019, 02:59 PM
Replies: 123
Views: 61,923
Posted By Lankku
Refueled -92 second time with E85 and visited the...

Refueled -92 second time with E85 and visited the dyno again. Gains are not big as expected, around the same relative to the change with the 2V modular. At least it'll be cheaper to daily it with E85...
Forum: performance & modifications 10-03-2019, 11:26 AM
Replies: 40
Views: 4,665
Posted By Lankku
You can try but be prepared if their service...

You can try but be prepared if their service hasn't improved lately. Several people, myself included, have not gotten any reply to emails and if you make an order, you won't even get an order...
Forum: projects & restorations 10-02-2019, 04:50 PM
Replies: 123
Views: 61,923
Posted By Lankku
A couple of days has passed again and something...

A couple of days has passed again and something has happened, again.

Adjusted the -92 rear shocks. 16 clicks is way too loose, 19 is a bit too loose also and 22 is too tight. Best so far is 20 and...
Forum: maintenance & nonperformance 10-02-2019, 04:22 PM
Replies: 1
Views: 566
Posted By Lankku
Might be the shield touching the disc, doesn't...

Might be the shield touching the disc, doesn't need much. If you have a spring plate for the pads' pins then that might be a little sideways and touch the outer edge of the disc.
Forum: performance & modifications 10-02-2019, 04:15 AM
Replies: 9
Views: 910
Posted By Lankku
For me front control arm rear and panhard...

For me front control arm rear and panhard bushings are the ones to change to poly. Even with a stockish suspension. Changes handling pretty nicely.
Forum: maintenance & nonperformance 09-28-2019, 06:07 PM
Replies: 6
Views: 831
Posted By Lankku
Have you tried with old clips if they are...

Have you tried with old clips if they are thinner? Sometimes I have had to use old clips because new ones were too thick and u-joint kept binding.
Forum: projects & restorations 09-25-2019, 05:20 PM
Replies: 123
Views: 61,923
Posted By Lankku
Bought a BC Racing coilover kit for the -92. It...

Bought a BC Racing coilover kit for the -92. It arrived yesterday and I installed it today after work. 7kg front springs, 4.5kg rear springs. Basic kit for 240 includes 6kg springs front and back....
Forum: projects & restorations 09-24-2019, 04:13 PM
Replies: 123
Views: 61,923
Posted By Lankku
Thanks. And here we go again, updates just...

Thanks.

And here we go again, updates just happen :blah:

-92 had been burning a lot of oil since assembling the new engine. A bit over a week ago after work took the head off and 3rd cylinder...
Forum: performance & modifications 09-24-2019, 03:12 PM
Replies: 15
Views: 1,458
Posted By Lankku
It's not difficult, requires some work but has...

It's not difficult, requires some work but has been done numerous times. With any turbo you'll have to do a complete exhaust anyway, so making a couple of small downpipes shouldn't be a problem.

I...
Forum: maintenance & nonperformance 09-20-2019, 03:47 PM
Replies: 4
Views: 589
Posted By Lankku
Change the ring gear to the original flywheel....

Change the ring gear to the original flywheel. Heat it and tap out.
Forum: performance & modifications 09-19-2019, 06:11 PM
Replies: 32
Views: 3,121
Posted By Lankku
Innovate MTX-L has been my favorite choice in...

Innovate MTX-L has been my favorite choice in several cars. The one in "B6284T" has been in use around 6 years. Current MTX-L Plus model has 4.9 LSU sensor and got one in the -92.

Have had one...
Forum: projects & restorations 09-12-2019, 05:01 AM
Replies: 123
Views: 61,923
Posted By Lankku
Hasn't been a problem with bigger numbers before,...

Hasn't been a problem with bigger numbers before, why would it be now? Some plastic tires might not have enough grip ;-)

With K31 1.7bar was the limit on 3rd gear when making a full pull from low...
Forum: projects & restorations 09-11-2019, 05:00 PM
Replies: 123
Views: 61,923
Posted By Lankku
"B6284T" has had new street tires for some time...

"B6284T" has had new street tires for some time now, old ones were worn out. Same Hankook Ventus V12 Evo2 and same size. Looks like front tires last max four summers and rears two, how that can be?
...
Forum: performance & modifications 09-01-2019, 04:06 PM
Replies: 5
Views: 1,391
Posted By Lankku
Yep, you need the BCM from that car. Immobilizer...

Yep, you need the BCM from that car. Immobilizer is coded to it. There could be someone who can reprogram a used one but normally they are locked after first time and can not be changed.
Forum: performance & modifications 09-01-2019, 05:43 AM
Replies: 5
Views: 1,391
Posted By Lankku
I'll assume the donor is around -04 or newer...

I'll assume the donor is around -04 or newer V70/S60/S80? You'll need CEM for the immobilizer and other functions go through it too. If the donor is -04 or newer S40/V50/C30 or V70III/etc. then...
Forum: projects & restorations 08-19-2019, 06:10 PM
Replies: 123
Views: 61,923
Posted By Lankku
Yep. Only mandatory equipment on almost all...

Yep. Only mandatory equipment on almost all non-timed trackdays has been a helmet for now. Some quarter mile and standing mile events require driving gloves, long sleeve shirt and pants.

Handling...
Forum: maintenance & nonperformance 08-19-2019, 05:13 PM
Replies: 2
Views: 1,216
Posted By Lankku
Nothin really special needed, some Torx bits,...

Nothin really special needed, some Torx bits, good impact gun to open and close 30mm crank nut and a vise for setting the <-98 tensioner.

Yes you can lift manifolds with the head. On a <-98...
Forum: projects & restorations 08-18-2019, 04:08 PM
Replies: 123
Views: 61,923
Posted By Lankku
That isn't too much then :) Seems like the...

That isn't too much then :)

Seems like the last update has been pretty far back. Though nothing revolutionary has happened since.

I assembled and installed a new engine for the -92.
Now the...
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 03:38 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.