home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: DailyDriverMods
Forum: aftermarket engine management 09-02-2020, 01:49 PM
Replies: 17
Views: 2,039
Posted By DailyDriverMods
The MAF burnoff cycle would be done as following:...

The MAF burnoff cycle would be done as following:

The MS2 got programmable outputs. One output would go high when:
runtime -> 20 minutes

This signal will be fed into a ATTINY microcontroller....
Forum: performance & modifications 08-30-2020, 07:09 AM
Replies: 19
Views: 3,540
Posted By DailyDriverMods
@Duder: Thanks for this writeup, this gives a...

@Duder:
Thanks for this writeup, this gives a good insight into the newer Garrett stuff.

@OttoB:
The bigger intercooler will be added, i have to buy one anyway and i like to have a bit more...
Forum: performance & modifications 08-27-2020, 07:22 PM
Replies: 19
Views: 3,540
Posted By DailyDriverMods
I was thinking that the B230F/16T combo would...

I was thinking that the B230F/16T combo would probably start knocking around ~0.8 bar boost on normal 93 (or 98 in Europe) pump gas. So even though it has 9.8:1 compression, ~1.0 bar boost can be...
Forum: aftermarket engine management 08-26-2020, 06:00 AM
Replies: 17
Views: 2,039
Posted By DailyDriverMods
Yup, i saw that it officially isn't allowed to...

Yup, i saw that it officially isn't allowed to use the MS firmware on it. But they won't license anything other than their own hardware (which isn't better than some of these "clones"), and they...
Forum: aftermarket engine management 08-25-2020, 06:49 PM
Replies: 17
Views: 2,039
Posted By DailyDriverMods
Swapping the MAF straight ahead indeed makes more...

Swapping the MAF straight ahead indeed makes more sense.. then i only would have to make the MAF map once. But i just have the tendency to overcomplicate things. :pow: The additional MAP sensor will...
Forum: aftermarket engine management 08-25-2020, 05:44 PM
Replies: 17
Views: 2,039
Posted By DailyDriverMods
I was planning to use a buffer opamp and a...

I was planning to use a buffer opamp and a resistor voltage divider to keep it nice between 0-5v but i'm afraid that it may add too much noise to the signal. Since the car is NA, it probably won't...
Forum: aftermarket engine management 08-25-2020, 05:02 PM
Replies: 17
Views: 2,039
Posted By DailyDriverMods
Well, i've looked into it and actually prefer the...

Well, i've looked into it and actually prefer the MAF tuning stuff since you directly measure the amount of air that enters the engine. It can always be ditched if it doesn't work out, i just don't...
Forum: aftermarket engine management 08-25-2020, 03:52 PM
Replies: 17
Views: 2,039
Posted By DailyDriverMods
LH2.4 to MS2 [MAF based]

So... I decided that switching to a MS2 in my daily driver is a great idea that shouldn't be too difficult and couldn't possibly go wrong. :roll:

The setup is going to be a B230F which running on...
Forum: performance & modifications 08-24-2020, 10:36 AM
Replies: 19
Views: 3,540
Posted By DailyDriverMods
Ah, i didn't see that. I just looked in the user...

Ah, i didn't see that. I just looked in the user settings menu and couldn't find anything to change the username, since i haven't posted that much with the other account i decided to make a new one....
Forum: performance & modifications 08-24-2020, 07:09 AM
Replies: 19
Views: 3,540
Posted By DailyDriverMods
I'm from Den Helder, which is where the boat...

I'm from Den Helder, which is where the boat leaves for Texel. I am first going to try the 16T, my wallet wasn't all that happy already with this purchase. My power goals are modest, ~220ft/lb...
Forum: performance & modifications 08-23-2020, 12:21 PM
Replies: 19
Views: 3,540
Posted By DailyDriverMods
Thumbs up auto660 here, i made a new account because i...

auto660 here, i made a new account because i wasn't happy with my user name

It seems indeed that the GT2056 takes a lot more effort to fit and the difference isn't THAT big with a 16T. So i just...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 11:50 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.