home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.05 seconds.
Search: Posts Made By: hiperfauto
Forum: maintenance & nonperformance 09-19-2020, 02:09 PM
Replies: 2
Views: 172
Posted By hiperfauto
Make sure the inner wire didn't pull out of the...

Make sure the inner wire didn't pull out of the gear in the trans when you pulled it off the speedometer. If not, you either need a new cable or gear.
Forum: maintenance & nonperformance 09-15-2020, 11:56 PM
Replies: 8
Views: 351
Posted By hiperfauto
Assuming this is for a 240, the adjusting screw...

Assuming this is for a 240, the adjusting screw was never available separately. It comes as an assembly.
...
Forum: projects & restorations 09-15-2020, 10:14 PM
Replies: 33
Views: 1,119
Posted By hiperfauto
http://volvo1800pictures.com/wb/2/20-06%20October%...

http://volvo1800pictures.com/wb/2/20-06%20October%201967%20Engine%20types%20001.jpg
Forum: maintenance & nonperformance 09-14-2020, 04:26 PM
Replies: 2
Views: 261
Posted By hiperfauto
Lubricate the rubber nubs with dish soap or...

Lubricate the rubber nubs with dish soap or something slippery so they come out with the least amount of effort but there's still a good chance they're gonna break off. Don't forget the nuts holding...
Forum: maintenance & nonperformance 09-13-2020, 12:51 PM
Replies: 5
Views: 475
Posted By hiperfauto
700's don't use a foam seal AFAIK but there...

700's don't use a foam seal AFAIK but there should be a rubber seal under the boot.


http://212.247.61.152/US/main.aspx?page=article&artno=1365840
...
Forum: performance & modifications 09-10-2020, 03:42 PM
Replies: 13
Views: 792
Posted By hiperfauto
I think the best solution would be to make an...

I think the best solution would be to make an aluminum bushing to reduce the size of the hole so the 140 clutch cable can be used. It'll need to have a flange so it doesn't pull through the hole in...
Forum: performance & modifications 09-10-2020, 01:21 PM
Replies: 21
Views: 934
Posted By hiperfauto
The rockers I bought from Topi were modified...

The rockers I bought from Topi were modified Kenne Bells. The KG Trimning rockers have offset rollers while the KB's have offset adjusters. I suspect KG had rockers custom made for their kit.

Topi...
Forum: maintenance & nonperformance 09-09-2020, 06:58 PM
Replies: 7
Views: 463
Posted By hiperfauto
I would try a known good solenoid before pulling...

I would try a known good solenoid before pulling the overdrive.
Forum: maintenance & nonperformance 09-09-2020, 01:15 PM
Replies: 1
Views: 290
Posted By hiperfauto
Any custom piston manufacturer will be able to...

Any custom piston manufacturer will be able to supply wrist pin locks.

https://www.cp-carrillo.com/pt-3543-hardware.html

Assuming they're for a B230 you can still get them from the dealer.
...
Forum: maintenance & nonperformance 09-08-2020, 09:53 PM
Replies: 5
Views: 461
Posted By hiperfauto
This is the proper way to test the ECU connector....

This is the proper way to test the ECU connector. I believe the EZK connector is the same.

http://hiperformanceautoservice.com/images/TestingLH_ComputerHarness.jpg
Forum: maintenance & nonperformance 09-07-2020, 01:57 PM
Replies: 18
Views: 808
Posted By hiperfauto
If the bearing is touching the pressure plate...

If the bearing is touching the pressure plate it's spinning.
Forum: maintenance & nonperformance 09-07-2020, 12:49 PM
Replies: 18
Views: 808
Posted By hiperfauto
Even some cable actuated clutches run with no...

Even some cable actuated clutches run with no free play.

http://hiperformanceautoservice.com/images/240TurboClutchSpring.jpg
Forum: maintenance & nonperformance 09-06-2020, 05:47 PM
Replies: 2
Views: 337
Posted By hiperfauto
The starter trigger is the lower one circled in...

The starter trigger is the lower one circled in green. The other connection is for the cold start injector and ballast resistor bypass on D-Jet and K-Jet cars.
...
Forum: maintenance & nonperformance 09-01-2020, 05:56 PM
Replies: 2
Views: 364
Posted By hiperfauto
The diameter of the cross shaft where the bushing...

The diameter of the cross shaft where the bushing rides is .705".
Forum: maintenance & nonperformance 09-01-2020, 01:22 PM
Replies: 7
Views: 425
Posted By hiperfauto
The English were using Imperial units back then...

The English were using Imperial units back then so they're 1¾" (44.45mm).
Forum: maintenance & nonperformance 09-01-2020, 01:18 PM
Replies: 7
Views: 425
Posted By hiperfauto
The Haynes SU carb book shows the AUD499 manual...

The Haynes SU carb book shows the AUD499 manual carbs and AUD511 auto carbs use the same springs and needles so I'm not sure what the difference is.

The Volvo parts catalog shows they both update...
Forum: maintenance & nonperformance 09-01-2020, 01:03 PM
Replies: 7
Views: 425
Posted By hiperfauto
237549 is a HIF6 rear carb for '72- 140 with LHD...

237549 is a HIF6 rear carb for '72- 140 with LHD and manual trans.
Forum: maintenance & nonperformance 09-01-2020, 12:07 PM
Replies: 4
Views: 671
Posted By hiperfauto
The wave washer is made of plastic. My...

The wave washer is made of plastic.



My brother is selling a NOS one.

https://forums.turbobricks.com/showthread.php?t=330394
Forum: maintenance & nonperformance 08-28-2020, 02:53 PM
Replies: 6
Views: 386
Posted By hiperfauto
The hose is connected to a small vent pipe that's...

The hose is connected to a small vent pipe that's attached to the dipstick tube. It's not supposed to be connected to anything.

I've seen this happen several times and I'm at a loss to explain the...
Forum: maintenance & nonperformance 08-27-2020, 02:44 PM
Replies: 42
Views: 1,719
Posted By hiperfauto
FYI VP sells an economy steel/aluminum gear set...

FYI VP sells an economy steel/aluminum gear set that has the correct holes for the factory pullers.

http://212.247.61.152/US/main.aspx?page=article&artno=270690AL
Forum: maintenance & nonperformance 08-26-2020, 07:17 PM
Replies: 3
Views: 474
Posted By hiperfauto
Actually, the early parts catalog shows the part...

Actually, the early parts catalog shows the part number was updated from 1205715 to 1272673.
Forum: maintenance & nonperformance 08-26-2020, 01:30 PM
Replies: 16
Views: 728
Posted By hiperfauto
It's probably just full of dirt or grease. I'm...

It's probably just full of dirt or grease. I'm pretty sure it's a CAM rack as they're the most common.

Can you verify the manufacturer from the pics? The CAM rack has a diamond shaped plate with 2...
Forum: maintenance & nonperformance 08-25-2020, 06:52 PM
Replies: 16
Views: 728
Posted By hiperfauto
That's a ZF rack. This is the CAM rack. It's...

That's a ZF rack.

This is the CAM rack. It's also #4 in this pic.

https://www.volvowholesalepartsdirect.com/images/parts/volvo/fullsize/GR-27184.jpg
Forum: maintenance & nonperformance 08-25-2020, 06:41 PM
Replies: 16
Views: 728
Posted By hiperfauto
Check the right side rack bushing. The one on the...

Check the right side rack bushing. The one on the rack inside the housing. Assuming it's a CAM rack, the plastic bushing breaks and the rack moves around inside the housing.

SuperPro makes a poly...
Forum: maintenance & nonperformance 08-25-2020, 12:59 PM
Replies: 14
Views: 984
Posted By hiperfauto
Make sure the air duct inside didn't get melted. ...

Make sure the air duct inside didn't get melted.

https://www.volvowholesalepartsdirect.com/images/parts/Volvo/parts/fullsize/GR-12991_14.png



:nod:
...
Forum: maintenance & nonperformance 08-21-2020, 01:31 PM
Replies: 7
Views: 474
Posted By hiperfauto
The connector for the speedometer has a tamper...

The connector for the speedometer has a tamper proof cover with 2 little tabs that will break when removed. Most people don't bother to replace it but they're still available last time I checked and...
Forum: maintenance & nonperformance 08-21-2020, 11:51 AM
Replies: 42
Views: 1,719
Posted By hiperfauto
It's 9/16"-18 for 6 bolt crank.

It's 9/16"-18 for 6 bolt crank.
Forum: maintenance & nonperformance 08-20-2020, 01:15 AM
Replies: 6
Views: 559
Posted By hiperfauto
http://hiperformanceautoservice.com/images/Service...

http://hiperformanceautoservice.com/images/ServiceLabel.jpg

There's a service label in the back of the car. The problem is that the racks will interchange so it may not be same as what originally...
Forum: maintenance & nonperformance 08-19-2020, 07:40 PM
Replies: 6
Views: 559
Posted By hiperfauto
ZF tie rods have a rubber disc on them for the...

ZF tie rods have a rubber disc on them for the rack boot.

https://www.ipdusa.com/uploads/images_products_slideshow/fullsize_17859.jpg

CAM tie rods don't.
...
Forum: maintenance & nonperformance 08-19-2020, 01:06 PM
Replies: 24
Views: 1,712
Posted By hiperfauto
I've got an '84 B23FT that has the CPS mounting...

I've got an '84 B23FT that has the CPS mounting holes.
Forum: maintenance & nonperformance 08-18-2020, 08:06 PM
Replies: 52
Views: 2,725
Posted By hiperfauto
And now I get to relay the story of the first...

And now I get to relay the story of the first clutch I installed on my '67 122. It was 1970 something and my trusty steed needed a clutch. Being a broke teenager I opted for the reman clutch from the...
Forum: maintenance & nonperformance 08-18-2020, 05:23 PM
Replies: 52
Views: 2,725
Posted By hiperfauto
Did you check the pilot bearing? If so, you may...

Did you check the pilot bearing? If so, you may want to re-read post #7.

I speak from experience. After installing a Sachs clutch and not being able to get it to disengage I removed it and...
Forum: maintenance & nonperformance 08-18-2020, 03:20 PM
Replies: 23
Views: 1,113
Posted By hiperfauto
FYI, the original countershaft bearing has an...

FYI, the original countershaft bearing has an external clip that's not on the NU304ECP bearing. You'll need to have a groove machined in the new bearing and re-use the clip.

You can kind of see...
Forum: maintenance & nonperformance 08-18-2020, 12:40 AM
Replies: 17
Views: 1,008
Posted By hiperfauto
Go ahead and take the belts and pulleys off. You...

Go ahead and take the belts and pulleys off. You can line up the timing marks once the cover is off.

http://hiperformanceautoservice.com/images/B21_B23TimingMarks.jpg
Forum: maintenance & nonperformance 08-17-2020, 04:36 PM
Replies: 13
Views: 920
Posted By hiperfauto
The manifold is probably warped and needs to be...

The manifold is probably warped and needs to be surfaced.
Forum: maintenance & nonperformance 08-17-2020, 03:55 PM
Replies: 4
Views: 568
Posted By hiperfauto
There should be some kind of valve to control...

There should be some kind of valve to control when vapors are drawn from the charcoal canister. Some are inline (34,42) and some are right on the canister (9). The valve only allows vapors to be...
Forum: maintenance & nonperformance 08-17-2020, 02:05 PM
Replies: 17
Views: 1,008
Posted By hiperfauto
http://hiperformanceautoservice.com/images/B23Pull...

http://hiperformanceautoservice.com/images/B23Pulley.jpg

When reinstalling the pulley only tighten the bolts closest to the AC compressor. Tighten the bolts/nuts a little at time, turn the crank...
Forum: maintenance & nonperformance 08-17-2020, 12:28 PM
Replies: 13
Views: 920
Posted By hiperfauto
Check for vacuum leaks by spraying carb cleaner...

Check for vacuum leaks by spraying carb cleaner around the manifold gaskets (including the plate between carbs), carb base gaskets, throttle shafts (primary and secondary) or a torn brake booster...
Forum: maintenance & nonperformance 08-16-2020, 12:55 PM
Replies: 7
Views: 664
Posted By hiperfauto
VP might have them in stock in their SC warehouse...

VP might have them in stock in their SC warehouse but you can probably get them at a good hardware store if you can get one off to measure it.
...
Forum: maintenance & nonperformance 08-14-2020, 08:45 PM
Replies: 23
Views: 1,113
Posted By hiperfauto
That doesn't sound good. I'm afraid you're going...

That doesn't sound good. I'm afraid you're going to have to open it up and take a look.

There are a total of 6 bearings in an M47, 2 of which are NLA.

If I had to guess I'd say it's the rear...
Forum: maintenance & nonperformance 08-14-2020, 07:21 PM
Replies: 2
Views: 439
Posted By hiperfauto
The temp sensor is in location 2. It'll be a 2...

The temp sensor is in location 2. It'll be a 2 wire sensor on an '87 740 though.

http://hiperformanceautoservice.com/images/B230SensorChart.jpg
...
Forum: maintenance & nonperformance 08-14-2020, 07:09 PM
Replies: 2
Views: 447
Posted By hiperfauto
The same part is used under the hood on most...

The same part is used under the hood on most 240's. They're under the dash on 740's.

They aren't expensive new.

https://www.tascaparts.com/oem-parts/volvo-junction-block-cover-9162425
Forum: maintenance & nonperformance 08-14-2020, 03:05 PM
Replies: 23
Views: 1,113
Posted By hiperfauto
This would concern me. I would definitely try to...

This would concern me. I would definitely try to locate the cause of this noise before installing the trans. Can you take a video of the noise and post it?
Forum: maintenance & nonperformance 08-14-2020, 12:34 AM
Replies: 16
Views: 1,188
Posted By hiperfauto
Some parts come up as discontinued on the online...

Some parts come up as discontinued on the online catalogs when they're actually still available. This is one of them. There are 97 of them in the warehouse in Sweden and you can order them from your...
Forum: performance & modifications 08-14-2020, 12:01 AM
Replies: 4
Views: 910
Posted By hiperfauto
Oversize pistons for B230 were only made in .3mm...

Oversize pistons for B230 were only made in .3mm (.012") and .6mm (.024") larger sizes. They're NLA from Volvo and most sources show them as discontinued but CVI has both sizes available and in...
Forum: maintenance & nonperformance 08-12-2020, 05:08 PM
Replies: 24
Views: 1,712
Posted By hiperfauto
Pull the trans brace that's bolted to the block...

Pull the trans brace that's bolted to the block between the pan and flywheel and see if one of the rear main seal housing bolts fell out.
Forum: maintenance & nonperformance 08-09-2020, 04:35 PM
Replies: 20
Views: 1,308
Posted By hiperfauto
While those nuts may fit the studs for the...

While those nuts may fit the studs for the downpipe these are the correct ones. The difference in price is astounding.

https://www.fcpeuro.com/products/volvo-lock-nut-985868
Forum: maintenance & nonperformance 08-09-2020, 04:10 PM
Replies: 52
Views: 2,725
Posted By hiperfauto
He tried starting it in gear with the clutch...

He tried starting it in gear with the clutch pedal depressed already. See post #5.

I don't think the TO bearing is in backwards. OP says the clutch pedal feels normal.
Forum: maintenance & nonperformance 08-08-2020, 06:37 PM
Replies: 52
Views: 2,725
Posted By hiperfauto
I had to go and see if it was physically possible...

I had to go and see if it was physically possible to install the TO bearing backwards and it is. It places the fork close to the front of the window in the bell housing so that the cable wont be able...
Forum: maintenance & nonperformance 08-08-2020, 04:28 PM
Replies: 52
Views: 2,725
Posted By hiperfauto
I don't see how you could have put the TO bearing...

I don't see how you could have put the TO bearing on backwards.

http://betaimages.imcparts.net/webapp/wcs/stores/servlet/imc/images/full/1220955_1.jpg
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 04:02 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.