Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Hello Guest, welcome to the initial stages of our new platform! You can find some additional information about where we are in the process of migrating the board and setting up our new software here
Okay I am lost call i can find is 240 stuff which does not fit the bill. 1992 740 with a late m46 was AW71. The automatic shifter has four connections
-Blue and Yellow with Black Connector - Went to AW71 overdrive solenoid (yellow wire & blue wire is blank)
-Brown and Blue with Yellow Connector...
New 15% ethanol AAA states it could harm older cars (pre 2001). So are we all screwed??? My brothers 88 740t already gets worst gas mileage and rubber fuel hoses cracking/leaked. Also my 960 gets 24 mpg hwy pure gas and 19 with %10 corn. Skynet???
Anyone one have any experience with 1996 960 fuel level sensor failures? I have a great working fuel level gauge however the sender is completely wrong. I can't get a new one anywhere.... ipd, FCP, Volvo dealer, Worldpac. No body sells new units. Has anyone try to repair theirs?
Car is a 1996 Volvo 960 wagon, I know standard Volvo FWD wheels fit no problem however I now have four C70 wheels with a offset of 45 MM instead of the normal 43 (just my luck). The wheels bolt up to my wife's 960 no problem but the tire rubs the strut. Ideas for adding 2-5 mm of space? I have...
What is everyone getting for a/c temperatures at the center vents. Both cars my 1989 740 and my wife's 1996 960 with fan on 2 and max cold getting 55F with outside temp 89F 100% humidity. Compressors no slipping low side 35-40 PSI and fully charged of course. Thoughts? Comments? Speeches?
A 1988 740 N/A B230F with a EZ117K to convert to a Turbo.
I have a complete B230FT long block from a 1991 740 so no skinny rod problems.
From everything I can find on Alldata the wiring looks the same. Just add a ballast resistor change some wires to the fuel pump relay, add over boost switch...
I have a 2001 V70 T5 with a 2.3L that thrown a rod (cly 3) So I need a motor. LKQ has them for $850 plus :grrr:
My 80,000 miles complete B230ft was $300 :/
However there are ALOT of turbo 2.4L on the cheap. I'm keeping all turbo bits stock so stock boost should be able to run on the 2.4? or am...
I have a complete 1988 745 turbo (auto) 2.2 LH
also
A complete 1990 744 turbo (manual) 2.4 LH
Im going to do the manual swap on the 745 but whats really needed to add 2.4?
Ok different,
MAF
Distributor
ECU Pin connector
My car 1990 740 tic
-15G with flat flange and 2.75 straight back exhaust, at 16 psi
-Rebuild head, heavy duty bearings and refreshed block.
Lots of nice other supporting mods.
The motor loves the boost but the clutch hates it...
I have been trying to search for the best junkyard injectors to run on my 1990 740 turbo. Green tops are easy but can I do better? I know brown tops are cool but I never find a ford in the yard with injectors....
Ideas?
<a target='_blank' title='ImageShack - Image And Video Hosting'...
Basic story,
1990 Volvo 740 turbo with blown m46
I bought cheap 1991 Volvo 240 m47
However did not have crossmember nor drive shaft.
Screwed
So while under my automatic 745 I noticed that crossmember looks the same!!!
Am I right? Also can I use the front drive shaft from a aw70 (front half)
Car 1988 Volvo 745 turbo
>rotor and cap are not new but in good shape
>plugs are new and proper gap
>new wires
>timing is spot on
>injectors clean
>head is fully rebuild
>compression
1:145 psi
2:136 psi
3:136 psi
4:162 psi
I don't like that but the OEM spec is max difference of 28 psi
so its...
What have people paid avg to get there m46 totally rebuild?
<a target='_blank' title='ImageShack - Image And Video Hosting' href='http://imageshack.us/photo/my-images/43/25849623443271990873252.jpg/'><img src='http://imageshack.us/a/img43/722/25849623443271990873252.jpg' border='0'/></a><br>
(quick story)
My car 1990 744 TIC made on a brand new OEM clutch at 13 psi made 198. some thing horsepower on the dyno. About 7 months of normal driving (sometimes punching it but no clutch slamming) And its slipping on 2ed and 3ed with anything past 6 psi. So I was thinking about a SPEC stage 2...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.